16. You have a DHCP server that runs Windows Server 2008.
You restore the DHCP database by using a recent backup.
You need to prevent DHCP clients from receiving IP addresses that are currently in use on the network.
What should you do?
A. Add the DHCP server option 15.
B. Add the DHCP server option 44.
C. Set the Conflict Detection value to 0.
D. Set the Conflict Detection value to 2.
Answer: D
17. Your company has an Active Directory domain. A server named Server1 runs the Network Access Policy
server role.
You need to disable IPv6 for all connections except for the tunnel interface and the IPv6 Loopback interface.
What should you do?
A. Run the netsh ras ipv6 set command.
B. Run the netsh interface ipv6 delete command.
C. Run ipv6.exe and remove the IPv6 protocol.
D. From Local Area Connection Properties, uncheck Internet Protocol Version 6 (TCP/IPv6).
Answer: D
18. Your network uses IPv4.
You install a server that runs Windows Server 2008 at a branch office. The server is configured with two network
interfaces.
You need to configure routing on the server at the branch office.
Which two actions should you perform? (Each correct answer presents part of the solution. Choose two.)
A. Install the Routing and Remote Access role.
B. Run the netsh ras ip set access ALL command.
C. Run the netsh interface ipv4 enable command.
D. Enable the IPv4 Router Routing and Remote Access option.
Answer: A D
19. Your company has an IPv4 Ethernet network.
A router named R1 connects your segment to the Internet. A router named R2 joins your subnet with a segment
named Private1. The Private1 segment has a network address of 10.128.4.0/26.
Your computer named WKS1 requires access to servers on the Private1 network.
The WKS1 computer configuration is as shown in the following table.
Network
Addresses
IPv4 Address
10.128.64.113
Subnet mask
255.255.252.0
Default Gateway
10.128.64.1
The routers are configured as shown in the following table.
Router ID
Addresses
R1 C interface 1
R1 C interface 2 (To Internet)
10.128.64.1
131.107.108.37
R2 C interface 1
R2 C interface 2
10.128.64.10
10.128.4.1
WKS1 is unable to connect to the Private1 network by using the current configuration.
You need to add a persistent route for the Private1 network to the routing table on WKS1.
Which command should you run on WKS1?
A. Route add -p 10.128.4.0/22 10.128.4.1
B. Route add Cp 10.128.4.0/26 10.128.64.10
C. Route add Cp 10.128.4.0 mask 255.255.255.192 10.128.64.1
D. Route add Cp 10.128.64.10 mask 255.255.255.192 10.128.4.0
Answer: B
20. Your company has a single Active Directory domain. All servers run Windows Server 2008.
The company network has 10 servers that perform as Web servers. All confidential files are located on a server
named FSS1.
The company security policy states that all confidential data must be transmitted in the most secure manner.
When you monitor the network, you notice that the confidential files that are stored on the FSS1 server are being
transmitted over the network without encryption.
You need to ensure that encryption is always used when the confidential files on the FSS1 server are transmitted
Pass4Side Microsoft 70-642
Pass4Side Help you pass any IT Exams! Page 10 of
10
over the network.
What are two possible ways to achieve this goal? (Each correct answer presents a complete solution. Choose two.)
A. Deactivate all LM and NTLM authentication methods on the FSS1 server.
B. Use IIS to publish the confidential files, activate SSL on the IIS server, and then open the files as a Web folder.
C. Use IPSec encryption between the FSS1 server and the computers of the users who need to access the
confidential files.
D. Use the Server Message Block (SMB) signing between the FSS1 server and the computers of the users who
want to access the confidential files.
E. Activate offline files for the confidential files that are stored on the FSS1 server. In the Folder Advanced
Properties dialog box, select the Encrypt contents to secure data option.
Answer: B C
More Infomation Visit: